Sealoflex Enviroflex Reinforcing Fabric - Icopal

Sealoflex Reinforcing Fabric

Sealoflex Reinforcing Fabric is a polyester based reinforcing fleece intended to be used as the reinforcing layer within the Enviroflex™ liquid waterproofing system.

The fleece, available in a number of widths in a standard weight for Enviroflex 15 & 20 Systems and in a Premium weight for the Enviroflex 25 System. The reinforcing fleece is embedded into the Enviroflex™ liquid applied waterproofing coating in a ‘wet-on-wet’ application

The Enviroflex™ system is suitable for use as an exposed membrane in both new and refurbishment projects, particularly where traditional methods of waterproofing may prove difficult.

It is intended for use where limited foot traffic is anticipated, but may also be used in conjunction with the Enviroflex™ Walkway System where clear designation of anti-skid passageways is required.

Product Range

Product Code Description Size
3101031 Sealoflex Reinforcing Fabric (1000mm) for Enviroflex 15 & 20 System 1.0m x 30m
3101032 Sealoflex Reinforcing Fabric (300mm) for Enviroflex 15 & 20 System 0.30m x 91.4m
3101579 Sealoflex Board Joint Fabric (100mm) used to tape board joints on new timber 0.10m x 91.4m
3101765 Sealoflex Premium Reinforcing Fabric (1000mm) for Enviroflex 25 System 1.0m x 50m
310764 Sealoflex Premium Reinforcing Fabric (300mm) for Enviroflex 25 System 0.3m x 50m


Product Data and Performance

Performance Data:
Roll Size Availability: 1.0 m x 50m
1.0 m x 30 m;
0.30 m x 91.4 m;
0.10 m x 91.4 m
Form: Solid
Standard Colour: White
Weight: Standard and Premium


Surface Preparation

Ensure the substrate is sound, clean, dry and free of frost, dust and debris, and any material which would hinder adhesion. Residual moisture in concrete substrates must not exceed 5% in the upper 2 cm.

Application Conditions

Apply only when atmospheric and substrate temperatures are greater than 5 °C. The surface of the substrate should be clean and dry and must be 3 °C above the dew point. If the surface is below or at dew point temperature then moisture can form at the surface and affect coating adhesion and curing.

Personal Protective Equipment (PPE) should be worn.

Coverage Rates

The Enviroflex™ System is applied ‘wet-on-wet’ allowing full membrane application in a single process.

The total application rate of Enviroflex™ Liquid Waterproof Coating depends on the porosity and texture of substrate and the system selected - see design guide.

Application Method

Prior to the application of the Enviroflex™ Liquid Waterproof Coating, prime the substrate with an appropriate Enviroflex™ Acrylic Primer or Enviroflex™ EP1 Primer, and allow to cure.

Apply approximately 1/3rd of the Enviroflex™ Liquid Waterproof Coating above the primed substrate as the base layer using a brush or roller.

Immediately apply the Sealoflex Reinforcing Fabric into the base layer and roll the surface with a perlon roller, eliminating potential air bubbles. Overlaps in the reinforcing fabric should be a minimum 75mm.

Apply immediately the remaining 2/3rd of Enviroflex™ Liquid Waterproof Coating above the reinforcing fabric as the top layer.

Roll out evenly until complete saturation is achieved. Ensure the overlap areas (above and below the overlapping fabric) are fully saturated to maintain continuity of the waterproofing system.

See Enviroflex™ Liquid Waterproof Coating product information sheet for coverage rates and installation guidance.

    Contact Icopal 0161 8654444

    Find Local Support

    To discuss your project in more detail please contact
    Your Local Area Manager


    Technical Support


    0330 123 4585



    Sales Enquiries & Orders


    0843 224 7400


    0843 224 7401


    Latest News

    Oscar heads for the limelight


    BMI helps Children in Need keep young people safe


    Everyone's a winner - that's the truth!


    BMI helps shield school children from sea storms


    The Roaring Twentie's – and 40's – see BMI take shape


    BMI's training facilities claim academy status


    Leeds duo take the hounours at BMI Apprentice of the Year


    This site uses cookies in accordance with our Website Privacy Policy. By continuing to browse the site you are agreeing to our use of cookies. To browse without the use of cookies, you can opt-out as explained in our Website Privacy Policy or adjust your cookie settings for your browser

    Icopal: We Protect Your Building