Tanking - Cold Applied Tanking Membranes - Icopal

Xtra-Load SA Self-Adhesive Tanking Membrane

Xtra-Load SA self adhesive is specifically designed for use as a waterproof tanking membrane in critical areas such as internal and external tanking of underground structures, reservoirs, subways, liftshafts and retaining walls.

Features & Benefits

  • Ease of application.
  • Resistant to tearing.
  • Compatible with all forms of DPM’s and DPC’s.
  • Joints and seals easily.
  • High water vapour resistance.

Product Range

Xtra-Load SA self adhesive tanking membrane is manufactured from tough, cross-laminated HDPE film, laminated to a 0.9mm thick layer of modified rubber bitumen adhesive. When correctly specified, installed and fully protected will provide an effective barrier to water and water vapour. Xtra-Load SA self adhesive is compatible with concrete and screeded substrates, smooth brick or blockwork.  

Product Code Description Roll Size Roll Weight
3000187 Xtra-Load SA Self Adhesive Tanking 19.05m x 1.05m 22kg


Product Data and Performance

Performance Data
Nominal Thickness: 1.0mm
Water Vapour Permeability: 0.5gm-2 / 24 hours
Water Vapour Resistance: 892 MNsg-1
Strength: 3.5N
Elongation: 300%
Puncture Resistance: 250N
Adhesion: 3.5N/mm


Durability: Xtra-Load® SA, when fully protected and subjected to normal service conditions, will provide an effective barrier to the transmission of water and water vapour for the lifetime of the structure in which it is incorporated.

Compatibility: Xtra-Load® SA is compatible with concrete, smooth brick and blockwork or screeded substrates, and is resistant to those chemicals with which it is likely to come into contact. However, care should be taken to prevent contact with mould oil and hydrocarbons.

Resistance To Puncture: Provided sharp objects are not present prior to and during installation of the protective layer, the membrane will not be damaged by normal foot traffic.

Resistance To Moisture: When completely sealed and consolidated Xtra-Load® SA will meet Building Regulations requirements in the resistance of the passage of moisture from the ground. The membrane is impervious to water. 

Loading: When these membranes are fully confined they may be regarded as having the same compressive strength as the containing material, however when building masonry off the membrane, a dpc material should be installed over the membrane to act as a crushing layer and protect the membrane from point loading.

Installation Details

Xtra-Load® SA must be installed in accordance with the requirements of 'BS 8102: Code of practice for protection of below ground structures against water from the ground' and 'BS 8000-0: 2014. Workmanship on construction sites. Introduction and general principles'. Tanking should be externally applied wherever possible and immediately protected.

Preparation Of Surface: All surfaces should have a smooth finish, free from cavities, projections and mortar deposits. Surfaces should be dry and free from dust and frost. Concrete surfaces should be dense.
Vertical surfaces of brick and blockwork should be dry and rendered to provide an even surface. Brick or blockwork not rendered must be flush pointed to give a smooth surface without sudden changes in level.

Priming: Prior to application of the membrane, a priming coat of Icopal SA Bitumen Primer must be applied to all surfaces and allowed to dry.

Angles And Corners: Where the horizontal surface meets the vertical surface, a 50 mm by 50 mm fillet should be used, reinforced with a strip of membrane. Reinforcing angles are formed by cutting a 300 mm strip of Xtra-Load® SA from the roll.

Membrane Application: The ideal application temperature range is 5°C to 35°C. At low temperatures the products will become progressively stiffer, which may make it difficult to handle. The membrane rolls should be left in a heated storage area until immediately before application.

The tanking membrane should be applied only when atmospheric and substrate temperatures are greater than 5 °C. The surface of the substrate should be clean and dry and must be 3 °C above the dew point. If the surface is below or at dew point temperature then moisture can form at the surface and affect membrane adhesion.

Apply Icopal SA Bitumen Primer by brush or roller and leave until dry (approx 45 minutes to 1 hour, depending on weather conditions). The release paper should be removed in a continuous strip for the first 500 mm of the roll and the membrane pressed firmly into position to ensure no air pockets are formed.

Xtra-Load® SA self-adhesive tanking membrane is supplied with a selvedge. Align adjacent rolls of Xtra-Load® SA tacky side down, allowing a side overlap of 50 mm and end overlaps of 100 mm. Peel back the release paper and the selvedge as laying progresses. Press down roll joints firmly to develop and immediately bond, and to ensure a water-tight seal. The use of a hand roller will aid in providing a firm seal.

Vertical work: The tanking membrane should be applied starting at the top of the section of vertical wall. Using the action of gravity to aid installation, the backing sheet should be removed and the membrane well rollered down working from the middle to the edges to remove any pockets of air and to ensure a full bond to the substrate.

Membrane Protection: On completion, the membranes must be immediately protected following a detailed inspection for damage and faults. To ensure Xtra-Load® SA membranes are not damaged during backfilling or by following trades, a screed, or non-rot protection board, such as the Xtra-Load® Protection Board, should be laid immediately following application.

    Contact Icopal 0161 8654444

    Find Local Support

    To discuss your project in more detail please contact
    Your Local Area Manager


    Technical Support


    0330 123 4585

    Email: technical.uk@bmigroup.com


    Sales Enquiries & Orders


    0843 224 7400


    0843 224 7401

    Email: sales.admin@bmigroup.com

    Latest News

    A new faster, safer, stronger and lighter metal tile solution from BMI


    Band of Builders and BMI team up for community project


    The search is on for the BMI Apprentice of the Year 2020


    Oscar heads for the limelight


    BMI helps Children in Need keep young people safe


    Everyone's a winner - that's the truth!


    This site uses cookies in accordance with our Website Privacy Policy. By continuing to browse the site you are agreeing to our use of cookies. To browse without the use of cookies, you can opt-out as explained in our Website Privacy Policy or adjust your cookie settings for your browser

    Icopal: We Protect Your Building